Here are plans to build a small motorcycle from any old BMX bike and get close to 100 miles per gallon in the process. The tools that I used were a welder, die-grinder, crescent wrench, and other smaller hand tools that are common around most people's homes. My finished product had a gear ratio of 12:72 or 1:6 this carried me (150
lbs.) at 30+ MPH!
Here are some pics of my bike right now:
Video:
Required Parts:
1. BMX Bike
2. Steel tubing about (4 ft.)
3. 3/16" or thicker flat stock (4 ft.)
4. 3 H.P. engine
5. Clutch (mine was 12 tooth)
6. Sprocket (mine was 72 tooth)
7. Chain compatible with your clutch and sprocket (mine was #35) (5ft.)
How to Build:
1. Remove all of the pedal assembly
2. After removing the pedal assembly measure the inside of the frame and compare it to the height of the tallest point on your motor. (most likely the spark plug)
3. Now we must redesign the frame to hold the engine. (It is quite simple all you need to do is bend the front support down till you have your desired height and finish it with a motor mount.
4. Build a motor mount to make the bottom part of your frame. (I welded two pieces of 3/16" flat stock together)
Here is a picture of the front frame after being cut and rewelded to make room for the motor. While I had the front apart I also cut the top part of the frame and took about an inch out of it to tilt the front end back and give it a board track racer look. I also welded a piece of thick sheet metal to the bottom of it to improve structural strength.
5. Once the frame is mocked up and you have fitted your engine to the motor mount and have the clutch on the motor (hint hint put the clutch on) Bolt the motor in and weld up the frame nice and tight. In my final version I put a support from the top of the frame to the bottom to prevent the frame from flexing. This is a must!!!!
LOOK RIGHT BEHIND THE ENGINE TO GET AN IDEA OF WHAT I MEAN
5. Build the sprocket and chain drive assembly. For this I put the rear tire on backwards because the motor needed to be mounted with the chain on the other side of the bike that what is normal for a pedal bike. Basically I moved the chain sprocket from the right side to the left. I then welded my 72 tooth sprocket onto the one used when it was a BMX bike. Make sure to line the sprocket and clutch gear up as close as possible to avoid complication with the chain falling off. Just the other day I was riding mine up a hill and the rear sprocket came loose. Upon further inspection I realized that the clutch I had welded the sprocket onto (BMX gear) is a left hand thread so when the bike is used normally the gear is tightened onto the tire as more forward force is applied, but after putting the tire on backwards I was unthreading it as I put more force on it. As of this article I have not fixed it but hope to have it working again soon.
7. Now all you need is brakes. I chose to use the stock bike brakes, but I highly recommend something better. The added weight and increased speed melts the stock pads and takes a good 25 ft to stop at full braking.
8. Now try it out and you will probable realize something isn't as strong as you thought or something needs to be tweaked. Don't feel bad it took me 3 weeks after building it to get it to the point where I could ride it up the street without breaking down and having to walk it home.
Misc:
***Disclaimer***
I am not responsible for ANYTHING and I mean anything that results from the use of any part of this article.
19 Comments to “BMX Cycle”
Write a comment
Email This Post
hi, just woundering, does he bike has a clutch and accelorator like a real motorbike. (on the hanle bars)?????
[Reply]
miles reply on October 19th, 2008:
It has brake and throttle on the handlebars. The clutch is a centrifugal clutch.
[Reply]
[...] out to be defective, but the welds do have good penetration and are strong. Just not pretty. Motor Mayhem Blog Archive BMX Cycle Let me know what you [...]
I was wondering about the gear ratio. Does this have enough torque to climb decent hills? Also, what is the max RPM’s for that engine (im comparing it to my 3hp 2-stroke snowblower engine)
[Reply]
miles reply on September 21st, 2008:
Yes it has enough power to climb reasonable size hills. I used an old briggs and stratton flathead and I believe it only revs to 3500 rpm. I am sure a 2-stroke can go much faster than that.
[Reply]
In the one photo it looks as if the chain rubs on the tubing that connects the left hand side of the wheel if what can be done to improve the design. Where can i look for a rear sproket
[Reply]
miles reply on September 3rd, 2008:
I got my rear sprocket from http://www.ebay.com just search “go kart 72 tooth sprocket”. Yes the chain does rub on the left hand fork for the rear tire. To solve this on my bike I just cut a section of the tubing out there. You can see this in this picture http://www.motormayhem.net/wp-uploads/2007/12/dscn4459.JPG . In the picture the chain is in front of the section cut off but that is because the chain is off the rear sprocket. When the chain is on the rear sprocket it runs smoothly in that cutout. I am pretty sure this greatly weakens that support, so I do not recommend that solution. To fix this correctly you would need to move the location where the chain goes around the motor (clutch) down so when the chain is tight it is at a less steep incline going to the rear sprocket and thus running under the rear fork. You might be able to achieve this by using a shorter motor or a larger bike and lowering the engine in relation to the rear sprocket. But you will need to determine the correct height based on you setup/bike. You could also experiment with running the chain inside the fork rather than outside it. This would eliminate the need to cross the rear fork at all.
Feel free to ask me something else if I didn’t make it clear.
Thanks,
Miles
[Reply]
where can i find a welder? for cheap and expensive.
Can you do this stuff in your garage or do you have to go somewhere?
[Reply]
miles reply on August 29th, 2008:
You could probably find one on http://www.craigslist.org, but you will need to get instruction on how to use it before you will be able to weld correctly. You can do it at home, but you need to be in a well ventilated area and use protective clothing. Thats what I do.
[Reply]
where can i find a clutch that i can install on to my engine?
[Reply]
miles reply on August 28th, 2008:
I got mine from http://www.ebay.com , just search “go kart clutch”.
[Reply]
where can i find a clutch that i can install on to the sprocket
is there anyway u can install it without a welder?
[Reply]
miles reply on August 21st, 2008:
What do you mean? The clutch is on the engine not the sprocket.
[Reply]
Man dude….who taught you how to weld? LOL.
Bike looks like a Death Trap.
[Reply]
Miles reply on July 31st, 2008:
Ya I know.
Normally I am pretty handy with a welder, but I was having trouble with my new welder and it was sputtering like crazy. I brought it back the next day and they said it had a defective transformer in it so I got it exchanged. I did make sure they have good penetration and they are pretty solid. Just not cosmetically pretty.
[Reply]
any suggestions on where to get a good but REALYREALY cheap bike for this project
[Reply]
miles reply on June 10th, 2008:
A scrap yard or a thrift store might have some cheap bikes, or craigslist.org may have some free ones in your area.
[Reply]
Hey, I have always wanted to build some kind of motorcycle thing but I’ve never had a motor. Where are some places i might be able to get a cheap motor. Also i was wondering how much this costs to build (just an estimate). If you could help me out here that would be much appreciated. Thanks
[Reply]
miles reply on March 25th, 2008:
For a motor I would check http://www.craigslist.org/about/sites.html or possibly http://www.ebay.com. I got mine from my local craigs-list page. The guy wanted to get rid of all his small engines so I got two 3HP and one 2HP for $25. As for the total cost it is going to depend on how much a motor costs. If you buy a new engine it will be way more than $25. I can’t remember what the clutch and sprocket cost but it was around $40 from ebay. The flat stock and other small parts I had on hand, but I can’t see it costing more than $25 from your local hardware store. I am going to say that it will be around $100 if you have a bike to use.
If you have more questions or comments I would be glad to answer them. Hope this helps you.
Thanks,
Miles
[Reply]